Vibration pump “Aquarius”: characteristics, pros and cons. Which vibration pump is better to choose for a well Vibrating pump Aquarius 1

10.07.2020

Raise water from a well or well using a pump. The Aquarius pump is characterized by users as a reliable and easy-to-use device. Manufactured by the Promelektro plant under the Vodoley brand, the pumps have a European Quality certificate and are inexpensive. The equipment is completed with domestic parts, with the exception of the thermal relay. The block is supplied from Germany from the Thermik company.

Types of pumps

Depending on the operating conditions, Aquarius pumps can be surface, submersible and deep. All pumps have two compartments - pump and motor. The operating principle of the working body is vibratory or centrifugal. General requirement– the pump operates only in an aqueous environment.

Aquarius surface pumps are installed near the well. The intake hose, also known as the suction pipe, can lift liquid to a level of up to 9 meters. Operating condition: before starting, the suction pipe must be under the fill, so a check valve must be installed on the line. The pump can pump out clean water from open reservoirs and wells, is easy to move, and is inexpensive. The line includes 3 models of the BC series, for pumping water with temperatures up to 35 0 C. The unit operates not noisily, since the single-phase motor has low power, the design is simple, not moisture-proof.

The Aquarius submersible pump starts working 10 minutes after being lowered into the chamber. An empty device cannot be turned on - breakdown is inevitable. The pump consists of a motor, working element, cable, float and discharge pipe. by hanging or stationary fastening. In this case, the kit should include protection against dry suction and a thermal relay. NVP series equipment is used. The equipment has lower productivity, but does not clog when working in muddy water. Products from the BCPEU series are also used. Submersible pumps are installed at a depth of up to 7 m with a capacity of up to 3.8 m 3 /hour. In this case, the cross-section of the casing pipe must be greater than 110 mm.

NVP vibration pumps can pump turbid liquid and are installed in small-section casing pipes, but they have a shorter service life. Therefore, users prefer centrifugal devices

If the well is deep, you must use Aquarius. A well is a product that has great power and can supply water from a well to the sand with the required pressure. These are centrifugal screw units with an extended working chamber. Models of the BTsPE series are installed on wells with a cross-section of 120 mm.

Aquarius deep pumps are installed in a deep artesian well. Applicable:

centrifugal;
vibrating membrane installations.

Vibration pumps can be installed even in a narrow pipe, since the housing is made with an outer section of 86 mm. Devices of the BTsPE and NVP series have an electric drive alternating current with mains voltage 220 V and frequency 50 Hz. The devices can supply the agent from a depth of 200 m to a height of up to 150 m. Depending on the performance, the weight of the Aquarius BCPE deep pump can reach 17.8 kg and have a linear dimension of up to 2.5 m. The deep mechanisms are equipped with all the necessary automation, the condensate box is removed beyond the well. During installation, the pump is placed at a level of 1.0 - 0.4 m from the bottom of the well in order to lift settled water.

The centrifugal pump for the Aquarius well is available in various modifications. They differ:

power;
pressure;
nominal and maximum flow;
size and number of steps.

The operation of a centrifugal pump is ensured by an engine, from the shaft of which rotation is transmitted to the impeller blades through a sealed partition. Depending on the purpose, several lifting stages are used, providing the necessary technical parameters.

The membrane apparatus does not have an impeller. The engine and work compartments are separated by a membrane. Due to the oscillatory movement from the rod, the necessary lifting force is created.

The manufacturer makes all pumps for pumping clean water from neutral materials permitted by standards. Stainless steel, brass, special polymers do not interact with the agent.

Submersible pumps are used more often. They work with constant engine cooling in stable conditions, which increases engine life. On average, submersible devices last 3 years longer than surface ones.

Design, principle of operation and application of the Aquarius-3 pump

The equipment operates from a single-phase network, pumps clean water with a temperature not exceeding 35 0 C, and is used with an immersion depth of 1-40 meters. The pump can operate for 2 hours with a break of 15 minutes. The device is produced with protection against electric shock of class I and II.

The Aquarius-3 pump belongs to the vibration class. The hydraulic chamber is a closed pipe space with a suction valve. Due to vibration produced by a special unit, the chamber is alternately filled and water is released into the discharge pipeline.

The pump must be secured in the casing. It is not permissible to hang it on the supply cable or extraction hose. From time to time it is necessary to inspect the structure for abrasion of the protective ring.

Technical characteristics of the Aquarius (Lepse) pump:

type – centrifugal, submersible;
productivity – 400 l/hour;
power 265 V;
immersion depth – 1-3 m;
weight – 4 kg.

The same device Aquarius-3 is used for pumping clean water. The pump is equipped with an automatic Thermik unit. The starting device is connected to the automation. The outlet fitting has a control valve - the flow and pressure change.

Description of the BCPE Aquarius pump for 110 mm pipe

The Aquarius 40 pump is installed on casing pipes with a cross-section of 110 mm; this is reflected in the marking by the presence of the letter U. The household pump is a truncated cone. A submersible device is used to pump water from containers and wells. The motor is single-phase, the working impeller is multi-stage. The engine is located in the oil compartment, but the entry of oil products into the water is prevented by the design of the labyrinths.

Water flow is regulated by shut-off valves at the discharge, but completely shutting off the supply while the pump is running is unacceptable. A pinched water supply hose to the container can cause the pump to overheat. When the engine is switched off by the protective relay, after the housing has cooled down, the unit will turn on automatically.

Technical characteristics of Aquarius 0.5-40U:

head up to 50 m;
productivity – 1.8 m 3 /hour;
engine power – 1 kW;
external section of the body – 104 mm

Voltage changes in the network, a clogged or broken hose can damage the pump. It is necessary to carry out Maintenance pump once every 2 years, checking the condition of the seals, cleaning the housing, and inspecting the working part.

A series of pumps with reduced water consumption.

The Aquarius 32 pump is designed for users who do not need high installation performance. This may be caused by a small flow of water into the receiving chamber of the well. On the other hand, high consumption is not needed for household needs. The 32 Series lineup is extensive. Several models have been created due to pressure options and the use of equipment in deep wells. The traditional good price/quality ratio has been expanded with additional equipment. The standard cable length is equal to the pressure in meters. The kit includes a nylon cable - suspension and a capacitor unit connected to the cable. At the same time, the Aquarius 0.32-140U pump can supply water from a depth of 150 m.

The advantages of the 32 series are considered:

the ability to operate equipment with low flow rates in nominal mode;
the devices are manufactured taking into account sanitary standards for the contact of the instrument with food materials;
there is a thermostat;
sufficient cable length;
low cost of the product.

The user can easily select an Aquarius brand pump for pumping water from any tanks and wells with temperatures below 35 0 C. Equipment of this brand has proven itself to be reliable and resistant to voltage surges. Some models can be used in obviously muddy water. In Russia, Aquarius pumps are sales leaders.

The equipment is repairable, spare parts are inexpensive, and you can disassemble and assemble the instrument yourself.

Pros and cons of the Aquarius pump - video

Despite great controversy regarding the reliability and feasibility of installing vibration models, Aquarius pumps consistently occupy their niche in the list of popular, budget-friendly, practical, easy-to-install and use models.

Applications and models

"Aquarius" is used:

for raising water from open sources (rivers, ponds, artificial lakes), as well as containers with a limited diameter (cisterns, tanks);
for pumping liquid from basements, trenches, pits;
for collecting drinking water from wells;
for watering small areas.

The pump is available in three modifications: Alpheus, Orion and Poseidon.

The models differ in their technical characteristics:

nominal and maximum volume of water supply;
power consumption;
dimensions (height and diameter);
nominal pressure;
the number of valves (the greater their number, the greater the water supply can be ensured).

The most powerful in its category is the BV-0.16-63-U5 Poseidon model. The power of the device is 230W, the water supply is from 580 to 2000 l/hour. Models with 2 valves are popular (although there are also four valves). The pump is capable of lifting water to a height of 30-80 m.

Features of operation

The pump belongs to the submersible mechanisms for pumping liquid, that is, the device is placed below the water surface, in the depth of a reservoir, container, trench.

If the water layer is smaller, or the device is too close to the bottom, the quality of the pumped liquid deteriorates, it becomes cloudy, as particles of silt, soil, sand from the bottom become suspended. Small particles are sucked in and rise with the water.

Moreover, the vibration pump mechanism lifts not only small particles, but also quite large pieces of soil that are not absorbed by the filter, but settle at the bottom of the well, the bottom of the well “silts up,” and the productivity of the aquifer decreases.

Therefore, normal and long-term operation of the vibration pump is possible if the well is drilled in soil with coarse sand and stone fractions.

Fine-grained sand, sooner or later, will clog the pump filter or, having penetrated inside, will damage the mechanism.

Vibrating pumps are used with caution in wells. The peculiarity of the pump's operation is reflected in the name. However, vibrations affect not only the operation of the mechanism itself (everything that vibrates wears out faster), but also the condition of the casing.

Specialist's note: vibration pumps are often purposefully used in the first stages of pumping wells to collect dirty water from wells.

Vibration affects the connection points of the mechanism parts. The piston and valve fasteners unscrew quickly. Therefore, in these places, some craftsmen immediately replace regular nuts with self-locking ones.

Advantages

The main advantages of Aquarius vibration pumps include:

Relatively low price.
Easy to use. The mechanism does not require frequent disassembly or lubrication of parts.
The mechanism is located in the depths of the water space and is completely washed by a layer of water. That is, water becomes a natural cooling component of the system.
Pump parts do not react to alkaline water levels. No salt deposits form on them.
The operation of the pump is practically not affected by the temperature of the surrounding liquid.
Compact, small-sized.
The device can be used in narrow wells and pipelines from 100 mm in diameter.
If necessary, it can be easily dismantled.

The most powerful pump of the BV-0.16-63-U5 Poseidon series (2 valves) has a sealed housing that prevents water from entering the mechanism. The body coating is protective and decorative.

The coating will acquire decorative and protective properties thanks to the powder coating technology used by electrophoresis. Applying a layer of powder polymers contributes to:

increasing the service life of the pump and its reliability;
increasing durability during long-term interaction between the mechanism and water.

In order to prevent overheating of the mechanism, the pump is equipped with protective automatic equipment. Overheating can occur as a result of a decrease in the water level and the mechanism running dry. For the pump to burn out, 10-30 seconds of idle operation are enough (if thermal protection is not installed).

However, with good soil quality, subject to safety precautions and normal operating conditions (alternating active water intake - 120 minutes and time for cooling the mechanism - 15 minutes), the vibration pump will last at least 5-8 years.

Watch the video, which shows the principle of operation of a vibration water pump, which fully applies to Aquarius vibration pumps:

The Aquarius vibration pump is the most reliable assistant at your dacha. This brand has firmly established itself in a leading position in the world market. Firstly, this is due to its affordability, and secondly, the quality of the products.

The Aquarius brand has a large range of water supply equipment:

These are pumps for working with dirty water, which has a high sand content;
electric pumps, with a centrifugal system.

All types of pumps differ in manufacturer parameters: power consumption; head of water; well diameter; number of valves; maximum volume of water supply.

Well pumps Aquarius

Well pumps include the following models:

Pump Aquarius BTsPE 0.32 - equipment productivity is 0.32 m 3 in 1 second, in 1 hour this is 3.6 m 3 of water. Constant pressure at a height of 40 meters.

There are two main models, which in turn have subtypes:

pump Aquarius BTsPE 1.2 – productivity reaches 1.2 m 3 per 1 sec. The pressure of the water column reaches 80 m. The weight of the pump also depends on the chosen model: from 7 to 24 kg.
Pump Aquarius BTsPE 1.6 – pump performance indicator is 1.6 m 3 per 1 sec. Stable water pressure at a height of 40 m. The weight of the device also depends on the type.

Drainage pumps Aquarius

Drainage - such a pump is used to pump dirty water from a newly dug well, or to drain basements.

Drainage pumps must have filter systems built into them to prevent solid particles from entering the equipment. The position in which such pumps are used is vertical.

The two-valve vibration pump Aquarius BV-0.14-63-U5 has the following characteristics:

According to reviews, the two-valve vibration pump Aquarius BV-0.14-63-U5 has the following advantages:

The Aquarius Poseidon vibration pump (BV-0.16-63-U5) with a four-valve water intake system is suitable for wells and wells with a diameter of 12 cm or more, the depth at which this pump operates reaches 100 meters.

This model is ideal for supplying drinking water and for use in gardening. The design of the Aquarius Poseidon pump is unique and made of high-quality materials.

The Aquarius vibration pump consists of an electric motor and pumping equipment.

Each pump is accompanied by an instruction manual with operating rules, which reflects the following:

If used correctly, the Aquarius vibration pump will serve you for a long time.

Benefits of using the Aquarius vibration pump:

On the official website of Vinnitsa you will find a full range of Aquarius vibration pumps.

The number of water wells in our country is constantly increasing, which means that the demand for household submersible pumps is constantly increasing. The most popular type in this classification are vibration devices. The proven manufacturing technology was laid down in the second half of the 20th century. This year, about 1 million pieces have already hit the shelves, although the market is not limited to this number. With such abundance, it’s hard to figure out on your own which vibration pump is better.

Some of the most famous names for such devices are “Baby” and “Spring”. However, recently the model range has expanded significantly due to local manufacturers and representatives of Chinese business.

Well hydraulics

When choosing which well pump is best for specific conditions, it is necessary to take into account a number of important operational factors:

the geometric and physical parameters of the well are taken into account;
the required volume of water for use in a country house or in a private house;
The price tag for the purchased copy plays an important role.

When choosing a pricing policy, you should take into account not only the payment for one pump, but the total price of a pumping station for a well, including main lines from the pipeline. The kit includes both home water supply and liquid supply to sheds with domestic animals, as well as wiring for watering garden crops.

It is advisable to ensure the availability of a spare water storage tank, as well as maximum automation of the system. This module will reduce the impact of water hammer in the system, and will also allow you to maintain the required pressure in the pipes at 2.5-3 atm.

Vibration pump design

The submersible vibration pump has a simple design. However, it does not require any additional maintenance, such as regular lubrication or mandatory preventative maintenance.

The device is based on several important modules:

electromagnet;
vibrator;
sealed housing.

An electromagnet consists of a metal core made of steel, as well as coils connected in a series circuit. The core is made in the form of a U-shape. It is composed of many sheet plates of the same shape.

There is also a working membrane, which provides additional fixation to the working rod. A pair of check valves are mounted on it to allow water to pass through in a timely manner.

VIDEO: Review and repair of a vibration pump

Using a vibration pump in a well

You can operate a vibration pump in a well at any convenient depth. It is worth considering that vibration can be reflected in the surrounding space. When the channel is made in stable rocks, for example in sandstone, clayey rocks or rocky soil, then such a device does not cause any complications.

But if there is instability of the soil, layers of quicksand rocks are noticed, then the vibration can slightly muddy the water. For further use of the liquid, you will need to use various filters. Excessive vibration can even contribute to clogging of the channels, which will negatively affect the inflow.

A positive quality that promotes the purchase of a vibration pump is its low price tag. However, if the water supply owner’s first priority is comfort, then they often pay attention to the use of pumping stations.

Additional electrical protection

If the pump in the well for water supply at home is vibrating, then it is recommended to install an electrical stabilizer before connecting it. The electrical appliance balances the voltage supply on weak power lines. The need for a stable current value lies in the fact that during start-up the pump is forced to consume a high starting current.

Also, during operation, “Baby” or “Spring” will produce a guaranteed pressure while maintaining the voltage at the same level. Any stabilizer can extend the life of the pump, because manufacturers calculate their characteristics based on stable values of voltage, current and frequency.

Choosing between models

When the owner of a country house has decided on the type of device, all that remains is to choose which vibration pump is best according to the model. For this purpose, appropriate search criteria are selected.

Performance

The value determines the amount of water pumped per hour. There are three groups:

minimum - up to 350 l/hour;
medium - 750 l/hour;
powerful 1500 l/hour or more.

Productivity is correlated with water debit. You shouldn’t take an extremely powerful one that can pump out all the water in a few minutes, and then you have to wait for it to come back again.

Pressure

The indicator is relevant for a significant distance of the consumer facility from the water intake point. The division goes like this:

the minimum for pumps is 40 m water column;
a sufficient average value of 60 m;
maximum for household appliances up to 90 m.

It is worth considering that the pressure is never excessive, since in the calculation about 20% should be lost for losses. When positioned horizontally, a distance of 10 m is equivalent to 1 m of immersion.

Water intake

There are two large types of intake, one draws water from below, and the second has an intake from above. The last option is the most optimal, since it does not take sand particles or large fractions of debris. It practically does not clog.

If the feedstock enters the vibration pump from below, then this effect is relevant for flushing freshly drilled wells. Suspensions are driven through the cavity, and small debris is easily washed away from work residues.

Housing material

Early models were made exclusively from aluminum. Such a body was easy to maintain, but could become covered with growths, and was also subject to corrosion processes in some places.

In the current environment, manufacturers offer plastic cases. They also behave comfortably when working with water, but are not susceptible to rust. The disadvantage of such specimens is the significant fragility of the body elements.

Star news